Customer Information Sheet

 

Thank you for purchacing shellac from the Shellac Shack. We stand behind our products and insist on your satisfaction.

Because we have no control over how our products are stored after they are shipped, our guarantee has a time limit. Please check our website under 'Terms & Conditions' for details.

 

Here is some information you may find helpful.

-Store you shellac flakes in a cool, dry place and they will remain fresh for years. Humidity and light are the 2 factors that effect the quality of shellac flakes. If the flakes should clump or cake together, this is called blocking. This can happen in warm weather, but does not indicate there is anything wrong with the flakes. Just break up the blocks and add to alcohol.

The Cut

With regards to shellac, the term “cut” refers to the proportion of shellac ( in pounds) to alcohol( in gallons ). Thus a 2 pound cut means 2 pounds of shellac flakes dissolved in a gallon of alcohol. Since few people would use a gallon of shellac for a project and because liquid shellac has a relatively short shelf life ( approximately 6 months ), it is best to mix up only what you think you will need. For example, to make a 2 pound cut you could mix ¼ pound of flakes with 1 pint of alcohol.

Below is a chart for mixing 8 - 10 ozs. of finish at various cuts:

#1 cut...........................1 oz flakes.....................8 oz alcohol

#2 cut...........................2 oz flakes.....................8 oz alcohol

#3 cut...........................3 oz flakes.....................8 oz alcohol

Of course you can make a little over a pint of finish by doubling the flakes and the alcohol.

The flakes can take up to 24 hours to completely dissolve. It helps to stir the solution every now and then.

After the flakes have totally dissolved, the liquid will need to be strained either with a fine mesh paint strainer or tightly woven cloth.

When dissolving the buttonlac it is best to crush the buttons, as they will dissolve much quicker. I wrap the buttons in a clean cloth and smack them with a hammer. Perhaps you have a more creative method.

There are 3 ways to remove the wax from buttonlac:

1.  
   1.  
      1.  

         1. Wrap the pulverized buttons in a double layer of large paper coffee filters. Tie the top closed and set this in the appropriate amount of alcohol.

         2. Dissolved the pulverized buttons in the alcohol, then filter it through a couple of large coffee filters. This method takes time as the solution filters through slowly. There is also some alcohol evaporation.

         3. Dissolve the pulverized buttons in the alcohol and allow the solution to sit for a number of weeks and then decant the dewaxed layer into another container. This method is the least recommended.

------------------

-Do not store shellac – either liquid or flakes - in a metal container.

-If your mixed shellac is over 6 months old, it is best to test it by pouring a drop on a hard nonporous surface such as glass or clean metal. If it does not dry to a hard surface in an hour or so, discard that batch and mix up a new one.

-Some folks talk about using chemical- grade ethanol to mix with their shellac flakes. I myself have never run into any problem using the denatured alcohol from the paint or hardware store. You will know if there is a problem if you get “ blushing” when the coat has dried. Blushing will indicate that either your alcohol has water in it, or you are applying the shellac on a very humid day.

Application

As with any stain or finish, it is wise to try it out on a scrap piece of the wood you are planning to finish.

In air temperatures above 70` the alcohol in shellac dries more quickly, so it is important to remember to move fairly quickly with your application and don't go back to catch spots you have missed. Because one coat of shellac burns into the next, any missed spots can be covered on the next coat and still produce a level finish.

If you are using shellac for the first time, or for the first time on a species of wood , it is wise to try it out on a piece of scrap along with any stain you plan to use , to see what you can expect as an end product.

Wipe-on or padded:

With padding, I use a 11/2 to 2 pound cut of shellac.

Use soft, lint-free cotton cloth formed into a pad. You can either put the shellac into a container so that you can 'blot' the pad against the side after you have dipped it into the finish. You can also put you shellac into a squeeze bottle and apply it to the pad this way. In either case you want enough shellac on the pad to moisten it, but not enough so that it drips.

I like to use as long a stroke along the surface as I can. I find I can usually cover an area, and even pass over it a second time to even out the material, but then I leave it. Remember, if you don't like the way the finish is laying down, you can fix it on the next coat. One of the benefits of using shellac!

Brushing

 

With brushing, I use a 1 to 11/2 pound cut of shellac. It is best to use a natural bristle brush or a Taklon synthetic brush. The method is similar to padding in that you don't want too much material on your brush and you want to move rather quickly. I sit the brush on the wood a ways from the edge as there tends to be a more material 'dropped' the initial contact. I move the brush in one direction, then back over the contact spot towards the other direction.

Spraying

Here, I will limit comments to spraying shellac is similar to spraying nitro-cellulose lacquer regarding application. They are also similar with respect to the problem of blushing. Lacquer retarder will prevent blushing with shellac.

I will not try to describe French Polishing here, but will suggest checking out books and articles by Jeff Jewett and Bob Flexner for detailed information on French Polishing and more on the above methods.